Window tape VARIO, white, full-wing, SK, interchangeable, 25mSK, interchangeable, 25mWindow tape VARIO, white, full-flush,SK,interchangeable, 25m. SK, interchangeable, 25m is used to seal the window connection joint. Due to the variable Sd value, this film can be used both indoors and outdoors. Areas of application: Window and door sealing indoors and outdoors. Installation instructions Window tape VARIO, white, full-flush, SK, interchangeable, 25m. SK, alternating, 25m All profile openings, e.g. cut edges of extensions and window sill profiles or continuous grooves in fitted roller shutter boxes, must be sealed with sealant. The surfaces to be bonded to the window frame and masonry must be clean and dry, free of dust, grease and release agents (e.g. new plastic profiles). The surface coating on wooden windows should be a few days old, as the solvents that otherwise escape can reduce the adhesion of the tape. If necessary, remove soiling with grease-dissolving cleaning agents. Ensure that the material is compatible. In the case of highly absorbent, sanding substrates, pre-treat the building structure with an adhesion promoter, e.g. DRG spray primer, DRG spray adhesive or solvent-free primer. In the event of break-outs in the masonry, a clean smooth coat must be applied again. When bonding, the tapes must be applied to the frame without creases, in parallel and pressed down all the way. Allow the tapes to overlap at the corners and seal them so that they are watertight against driving rain. bond airtight. Movement absorption must be ensured by creating sufficient loops in the area of the connection joint. Minimum adhesive width on the window 15 mm, on the wall at least 30 mm The sealing tape must be sufficiently bonded to the masonry in the area of the subsequent plaster cover (rule of thumb: at least 75 % of the contact surface).

Window tape VARIO, white, full-wing, SK, interchangeable, 25mSK, interchangeable, 25mWindow tape VARIO, white, full-flush,SK,interchangeable, 25m. SK, interchangeable, 25m is used to seal the window connection joint. Due to the variable Sd value, this film can be used both indoors and outdoors. Areas of application: Window and door sealing indoors and outdoors. Installation instructions Window tape VARIO, white, full-flush, SK, interchangeable, 25m. SK, alternating, 25m All profile openings, e.g. cut edges of extensions and window sill profiles or continuous grooves in fitted roller shutter boxes, must be sealed with sealant. The surfaces to be bonded to the window frame and masonry must be clean and dry, free of dust, grease and release agents (e.g. new plastic profiles). The surface coating on wooden windows should be a few days old, as the solvents that otherwise escape can reduce the adhesion of the tape. If necessary, remove soiling with grease-dissolving cleaning agents. Ensure that the material is compatible. In the case of highly absorbent, sanding substrates, pre-treat the building structure with an adhesion promoter, e.g. DRG spray primer, DRG spray adhesive or solvent-free primer. In the event of break-outs in the masonry, a clean smooth coat must be applied again. When bonding, the tapes must be applied to the frame without creases, in parallel and pressed down all the way. Allow the tapes to overlap at the corners and seal them so that they are watertight against driving rain. bond airtight. Movement absorption must be ensured by creating sufficient loops in the area of the connection joint. Minimum adhesive width on the window 15 mm, on the wall at least 30 mm The sealing tape must be sufficiently bonded to the masonry in the area of the subsequent plaster cover (rule of thumb: at least 75 % of the contact surface).

Window tape VARIO, white, full-wing, SK, interchangeable, 25mSK, interchangeable, 25mWindow tape VARIO, white, full-flush,SK,interchangeable, 25m. SK, interchangeable, 25m is used to seal the window connection joint. Due to the variable Sd value, this film can be used both indoors and outdoors. Areas of application: Window and door sealing indoors and outdoors. Installation instructions Window tape VARIO, white, full-flush, SK, interchangeable, 25m. SK, alternating, 25m All profile openings, e.g. cut edges of extensions and window sill profiles or continuous grooves in fitted roller shutter boxes, must be sealed with sealant. The surfaces to be bonded to the window frame and masonry must be clean and dry, free of dust, grease and release agents (e.g. new plastic profiles). The surface coating on wooden windows should be a few days old, as the solvents that otherwise escape can reduce the adhesion of the tape. If necessary, remove soiling with grease-dissolving cleaning agents. Ensure that the material is compatible. In the case of highly absorbent, sanding substrates, pre-treat the building structure with an adhesion promoter, e.g. DRG spray primer, DRG spray adhesive or solvent-free primer. In the event of break-outs in the masonry, a clean smooth coat must be applied again. When bonding, the tapes must be applied to the frame without creases, in parallel and pressed down all the way. Allow the tapes to overlap at the corners and seal them so that they are watertight against driving rain. bond airtight. Movement absorption must be ensured by creating sufficient loops in the area of the connection joint. Minimum adhesive width on the window 15 mm, on the wall at least 30 mm The sealing tape must be sufficiently bonded to the masonry in the area of the subsequent plaster cover (rule of thumb: at least 75 % of the contact surface).

Window tape VARIO, white, full-wing, SK, interchangeable, 25mSK, interchangeable, 25mWindow tape VARIO, white, full-flush,SK,interchangeable, 25m. SK, interchangeable, 25m is used to seal the window connection joint. Due to the variable Sd value, this film can be used both indoors and outdoors. Areas of application: Window and door sealing indoors and outdoors. Installation instructions Window tape VARIO, white, full-flush, SK, interchangeable, 25m. SK, alternating, 25m All profile openings, e.g. cut edges of extensions and window sill profiles or continuous grooves in fitted roller shutter boxes, must be sealed with sealant. The surfaces to be bonded to the window frame and masonry must be clean and dry, free of dust, grease and release agents (e.g. new plastic profiles). The surface coating on wooden windows should be a few days old, as the solvents that otherwise escape can reduce the adhesion of the tape. If necessary, remove soiling with grease-dissolving cleaning agents. Ensure that the material is compatible. In the case of highly absorbent, sanding substrates, pre-treat the building structure with an adhesion promoter, e.g. DRG spray primer, DRG spray adhesive or solvent-free primer. In the event of break-outs in the masonry, a clean smooth coat must be applied again. When bonding, the tapes must be applied to the frame without creases, in parallel and pressed down all the way. Allow the tapes to overlap at the corners and seal them so that they are watertight against driving rain. bond airtight. Movement absorption must be ensured by creating sufficient loops in the area of the connection joint. Minimum adhesive width on the window 15 mm, on the wall at least 30 mm The sealing tape must be sufficiently bonded to the masonry in the area of the subsequent plaster cover (rule of thumb: at least 75 % of the contact surface).

Window tape VARIO, white, full-wing, SK, interchangeable, 25mSK, interchangeable, 25mWindow tape VARIO, white, full-flush,SK,interchangeable, 25m. SK, interchangeable, 25m is used to seal the window connection joint. Due to the variable Sd value, this film can be used both indoors and outdoors. Areas of application: Window and door sealing indoors and outdoors. Installation instructions Window tape VARIO, white, full-flush, SK, interchangeable, 25m. SK, alternating, 25m All profile openings, e.g. cut edges of extensions and window sill profiles or continuous grooves in fitted roller shutter boxes, must be sealed with sealant. The surfaces to be bonded to the window frame and masonry must be clean and dry, free of dust, grease and release agents (e.g. new plastic profiles). The surface coating on wooden windows should be a few days old, as the solvents that otherwise escape can reduce the adhesion of the tape. If necessary, remove soiling with grease-dissolving cleaning agents. Ensure that the material is compatible. In the case of highly absorbent, sanding substrates, pre-treat the building structure with an adhesion promoter, e.g. DRG spray primer, DRG spray adhesive or solvent-free primer. In the event of break-outs in the masonry, a clean smooth coat must be applied again. When bonding, the tapes must be applied to the frame without creases, in parallel and pressed down all the way. Allow the tapes to overlap at the corners and seal them so that they are watertight against driving rain. bond airtight. Movement absorption must be ensured by creating sufficient loops in the area of the connection joint. Minimum adhesive width on the window 15 mm, on the wall at least 30 mm The sealing tape must be sufficiently bonded to the masonry in the area of the subsequent plaster cover (rule of thumb: at least 75 % of the contact surface).