Window connection tape INSIDE, red, full-flush SK, 25mSK, 25mInterior window connection tape consists of a plasterable fleece composite with 1 SK strip, optionally laminated with butyl strips on one side or alternating sides. The interior connection tape is used for fast and secure interior, airtight and vapour-retardant sealing of window connection joints and can also be used as an interior seal that can be plastered over. On highly porous substrates, we recommend a primer coat of butyl & bitumen primer when bonding with butyl. Installation instructions INSIDE window connection tape, red, full-fl. SK, 25m All profile openings e.g. Cut edges of extensions and window sill profiles or continuous grooves in fitted roller shutter boxes must be sealed with sealant. The surfaces to be bonded on the window frame and masonry must be clean and dry, free of dust, grease and separating agents (e.g. new plastic profiles). The surface coating on wooden windows should be a few days old, as the solvents that otherwise escape can reduce the adhesion of the tape. If necessary, remove soiling with grease-dissolving cleaning agents. Pay attention to the material compatibility. In the case of highly absorbent, sandy substrates, treat the building structure with an adhesion promoter, e.g. Pre-treat with DRG spray primer, DRG spray adhesive or solvent-free primer. In the event of break-outs in the masonry, a clean smooth coat must be applied again. When bonding, the tapes must be applied to the frame without creases, parallel and pressed down all the way. Allow the tapes to overlap at the corners and bond them so that they are watertight against driving rain or airtight. Movement absorption must be ensured by creating sufficient loops in the area of the connection joint. Minimum adhesive width on the window 15 mm, on the wall at least 30 mm The sealing tape must be sufficiently bonded to the masonry in the area of the subsequent plaster cover (rule of thumb: at least 75 % of the contact surface).

Window connection tape INSIDE, red, full-flush SK, 25mSK, 25mInterior window connection tape consists of a plasterable fleece composite with 1 SK strip, optionally laminated with butyl strips on one side or alternating sides. The interior connection tape is used for fast and secure interior, airtight and vapour-retardant sealing of window connection joints and can also be used as an interior seal that can be plastered over. On highly porous substrates, we recommend a primer coat of butyl & bitumen primer when bonding with butyl. Installation instructions INSIDE window connection tape, red, full-fl. SK, 25m All profile openings e.g. Cut edges of extensions and window sill profiles or continuous grooves in fitted roller shutter boxes must be sealed with sealant. The surfaces to be bonded on the window frame and masonry must be clean and dry, free of dust, grease and separating agents (e.g. new plastic profiles). The surface coating on wooden windows should be a few days old, as the solvents that otherwise escape can reduce the adhesion of the tape. If necessary, remove soiling with grease-dissolving cleaning agents. Pay attention to the material compatibility. In the case of highly absorbent, sandy substrates, treat the building structure with an adhesion promoter, e.g. Pre-treat with DRG spray primer, DRG spray adhesive or solvent-free primer. In the event of break-outs in the masonry, a clean smooth coat must be applied again. When bonding, the tapes must be applied to the frame without creases, parallel and pressed down all the way. Allow the tapes to overlap at the corners and bond them so that they are watertight against driving rain or airtight. Movement absorption must be ensured by creating sufficient loops in the area of the connection joint. Minimum adhesive width on the window 15 mm, on the wall at least 30 mm The sealing tape must be sufficiently bonded to the masonry in the area of the subsequent plaster cover (rule of thumb: at least 75 % of the contact surface).

Window connection tape INSIDE, red, full-flush SK, 25mSK, 25mInterior window connection tape consists of a plasterable fleece composite with 1 SK strip, optionally laminated with butyl strips on one side or alternating sides. The interior connection tape is used for fast and secure interior, airtight and vapour-retardant sealing of window connection joints and can also be used as an interior seal that can be plastered over. On highly porous substrates, we recommend a primer coat of butyl & bitumen primer when bonding with butyl. Installation instructions INSIDE window connection tape, red, full-fl. SK, 25m All profile openings e.g. Cut edges of extensions and window sill profiles or continuous grooves in fitted roller shutter boxes must be sealed with sealant. The surfaces to be bonded on the window frame and masonry must be clean and dry, free of dust, grease and separating agents (e.g. new plastic profiles). The surface coating on wooden windows should be a few days old, as the solvents that otherwise escape can reduce the adhesion of the tape. If necessary, remove soiling with grease-dissolving cleaning agents. Pay attention to the material compatibility. In the case of highly absorbent, sandy substrates, treat the building structure with an adhesion promoter, e.g. Pre-treat with DRG spray primer, DRG spray adhesive or solvent-free primer. In the event of break-outs in the masonry, a clean smooth coat must be applied again. When bonding, the tapes must be applied to the frame without creases, parallel and pressed down all the way. Allow the tapes to overlap at the corners and bond them so that they are watertight against driving rain or airtight. Movement absorption must be ensured by creating sufficient loops in the area of the connection joint. Minimum adhesive width on the window 15 mm, on the wall at least 30 mm The sealing tape must be sufficiently bonded to the masonry in the area of the subsequent plaster cover (rule of thumb: at least 75 % of the contact surface).

Window connection tape INSIDE, red, full-flush SK, 25mSK, 25mInterior window connection tape consists of a plasterable fleece composite with 1 SK strip, optionally laminated with butyl strips on one side or alternating sides. The interior connection tape is used for fast and secure interior, airtight and vapour-retardant sealing of window connection joints and can also be used as an interior seal that can be plastered over. On highly porous substrates, we recommend a primer coat of butyl & bitumen primer when bonding with butyl. Installation instructions INSIDE window connection tape, red, full-fl. SK, 25m All profile openings e.g. Cut edges of extensions and window sill profiles or continuous grooves in fitted roller shutter boxes must be sealed with sealant. The surfaces to be bonded on the window frame and masonry must be clean and dry, free of dust, grease and separating agents (e.g. new plastic profiles). The surface coating on wooden windows should be a few days old, as the solvents that otherwise escape can reduce the adhesion of the tape. If necessary, remove soiling with grease-dissolving cleaning agents. Pay attention to the material compatibility. In the case of highly absorbent, sandy substrates, treat the building structure with an adhesion promoter, e.g. Pre-treat with DRG spray primer, DRG spray adhesive or solvent-free primer. In the event of break-outs in the masonry, a clean smooth coat must be applied again. When bonding, the tapes must be applied to the frame without creases, parallel and pressed down all the way. Allow the tapes to overlap at the corners and bond them so that they are watertight against driving rain or airtight. Movement absorption must be ensured by creating sufficient loops in the area of the connection joint. Minimum adhesive width on the window 15 mm, on the wall at least 30 mm The sealing tape must be sufficiently bonded to the masonry in the area of the subsequent plaster cover (rule of thumb: at least 75 % of the contact surface).

Window connection tape INSIDE, red, full-flush SK, 25mSK, 25mInterior window connection tape consists of a plasterable fleece composite with 1 SK strip, optionally laminated with butyl strips on one side or alternating sides. The interior connection tape is used for fast and secure interior, airtight and vapour-retardant sealing of window connection joints and can also be used as an interior seal that can be plastered over. On highly porous substrates, we recommend a primer coat of butyl & bitumen primer when bonding with butyl. Installation instructions INSIDE window connection tape, red, full-fl. SK, 25m All profile openings e.g. Cut edges of extensions and window sill profiles or continuous grooves in fitted roller shutter boxes must be sealed with sealant. The surfaces to be bonded on the window frame and masonry must be clean and dry, free of dust, grease and separating agents (e.g. new plastic profiles). The surface coating on wooden windows should be a few days old, as the solvents that otherwise escape can reduce the adhesion of the tape. If necessary, remove soiling with grease-dissolving cleaning agents. Pay attention to the material compatibility. In the case of highly absorbent, sandy substrates, treat the building structure with an adhesion promoter, e.g. Pre-treat with DRG spray primer, DRG spray adhesive or solvent-free primer. In the event of break-outs in the masonry, a clean smooth coat must be applied again. When bonding, the tapes must be applied to the frame without creases, parallel and pressed down all the way. Allow the tapes to overlap at the corners and bond them so that they are watertight against driving rain or airtight. Movement absorption must be ensured by creating sufficient loops in the area of the connection joint. Minimum adhesive width on the window 15 mm, on the wall at least 30 mm The sealing tape must be sufficiently bonded to the masonry in the area of the subsequent plaster cover (rule of thumb: at least 75 % of the contact surface).